KI-PD Intelligent Smoke Detector

Manufacture: kidde

Product code: KI-PD

The KI-PD optical smoke detector ⭐
✅ brings advanced sensing technology to a practical design that increases efficiency ⭐
✅ saves installation time, cuts costs, and extends life safety and property protection capabilities. Continuous self-diagnostics ensure reliability over the long-haul, while environmental compensation helps reduce maintenance costs. Like all KI Series detectors, the KI-PD is an intelligent device that gathers analog information its optical sensor, converting this data digital signals. To make an alarm decision, the detector’s on-board microprocessor measures and analyzes sensor readings and compares this information to historical data. Digital filters remove signal patterns that are not typical of fires, thus virtually eliminating unwanted alarms.

Product information

Standard Features

Note: Some features described here may not be supported by all control systems. Check your control panel’s Installation and Operation Guide for details.

• Next generation optical smoke sensing technology

• Wide 0.53 to 3.94 %/ft. (1.7 to 12.35 %/m) smoke obscuration

• Uses Existing Wiring

• Automatic Device Mapping

• Up To 250 Total Addresses Per Loop

• Two Levels of Environmental Compensation

• Two Levels of Dirty Detector Warning

• Twenty Pre-Alarm Settings

• Five Sensitivity Settings

• Non-Volatile Memory

• Electronic Addressing

• Identification of Dirty or Defective Detectors

• Automatic Day/Night Sensitivity Adjustment

• Bicolor (Green/Red) Status Led

• Standard, Relay, Fault Isolator, and Audible Mounting Bases

• Sensor Markings Provide Easy Testing Identification

Application

The KI-PD detects extremely small particles of combustion and triggers an alarm at the first sign of smoke. Thanks to its highperformance forward-scattering reflective response technology, the photoelectric smoke sensor responds quickly and reliably to a wide range of fire types, especially slow burning fires fuelled by combustibles typically found in modern multi-use buildings.

Standard Detector Base, KI-SB, KI-SB4

This is the basic mounting base for Kidde KI Series detectors. The GSA-LED Remote LED is supported by this Base

KI-PD Intelligent Smoke Detector

Isolator Detector Base, KI-IB, KI-IB4

This base includes a built-in line fault isolator for use on Class A circuits. A detector must be installed for it to operate. The isolator base does not support the GSA-LED Remote LED.

The isolator operates as follows:

- a short on the line causes all isolators to open within 23 msec

- at 10 msec intervals, beginning on one side of the class A circuit nearest the loop controller, the isolators close to provide the next isolator down the line with power

- when the isolator next to the short closes, it reopens within 10 msec.

The process repeats beginning on the other side of the loop controller.

KI-PD Intelligent Smoke Detector

Audible Sounder Bases, Fire Mode

AB4GT, AB4G, AB4G-LF sounder bases

KI-PD Intelligent Smoke Detector

Dimensions

KI-PD Intelligent Smoke Detector

Specifications

Operating voltage	15.20 to 19.95 VDC
Normal operating current	51 µA
Alarm current	68 µA
Smoke Sensitivity Range	UL/ULC: 0.53 to 3.94 %/ft. (1.7 to 12.35 %/m) obscuration
Vibration level	10 to 35 Hz, with an amplitude of 0.01 in.10 to 35 Hz, with an amplitude of 0.01 in.
Air velocity	0 to 4,000 ft./min (0 to 20 m/s)
Wall mounting	12 in. (305 mm) max. ceiling
Compatible bases	See Ordering Information
Compatible detector testers	Testifire 1000, Testifire 2000
Operating environment	32 to 120°F (0 to 49°C), 0 to 93% RH, noncondensing
Construction	High Impact Engineering Polymer, White
Storage temperature	-4 to 140°F (-20 to 60°C)
Environmental compensation	Automatic
Agency Listings	CAN/ULC-S529, UL 268, UL 268A

Ordering Information

Catalog Number	Descriptio	Ship Wt. lbs (kg)
KI-PD	Intelligent Optical Smoke Detector	0.4 (0.16)

Accessories

KI-SB	Detector Mounting Base - Standard	0.2 (.09)
KI-SB4	4-inch Detector Mounting Base c/w Trim Skirt
KI-RB	Detector Mounting Base w/Relay
KI-RB4	4-inch Detector Mounting Base w/Relay, c/w Trim Skirt
KI-IB	Detector Mounting Base w/Fault Isolator
KI-IB4	4-inch Detector Mounting Base w/ Fault Isolator, c/w Trim Skirt
GSA-LED	Remote Alarm LED (not for EN54 applications)
KI-ABST	Audible (Sounder) Base for Fire Detectors	0.3 (0.15)
KI-ABLT	Low Frequency Audible (Sounder) Base for CO and Fire Detectors	0.3 (0.15)
KI-ABDT	Audible (Sounder) Base for CO and Fire Detectors	0.3 (0.15)
GSA-TS4	Trim Skirt (supplied with 4-inch bases)	0.1 (0.04)
GSA-TS	Trim Skirt - (optional for non 4-inch bases)	0.1 (0.04)
GSA-DMP	Detector Mounting Plate	3.0 (1.4)