GSA-MCC1 Single Input (Riser) Signal Module

GSA-MCC1 Single Input (Riser) Signal Module

Manufacture: kidde

Product code: GSA-MCC1

GSA-MCC1 Single Input Signal Modules is part of Kidde's Signature Series system ⭐
✅ They are intelligent analog addressable devices used for connecting, upon command the loop controller, supervised Class B signal or telephone circuits to their respective power inputs. The power inputs may be polarized 24 Vdc to operate audible and visible signal appliances or 25 and 70 VRMS to operate audio evacuation speakers and firefighter’s telephones ⭐
✅ The actual operation of the GSA-MCC1 is determined by the “personality code” selected by the installer. It is downloaded to the module the Signature loop controller during system configuration.

Product information

Standard Features

• Single and Dual input (riser) Use for connecting supervised 24 Vdc Audible/Visible signal circuits, or 25 and 70 VRMS Audio Evacuation and Telephone circuits to their power inputs.

• Ring-tone generator When configured for telephone circuits, the GSA-CC1 generates its own ring-tone signal eliminating the need for a separate ring-tone circuit.

• Plug-in (UIO) or standard 2-gang mount UIO versions allow quick installation where multiple modules are required. The 2-gang mount version is ideal for remote locations that require a single module.

• Automatic device mapping Signature modules transmit information to the loop controller regarding their circuit locations with respect to other Signature devices on the wire loop.

• Electronic addressing Programmable addresses are downloaded the loop controller, a PC, or the SIGA-PRO Signature Program/Service Tool; there are no switches or dials to set.

• Intelligent device with microprocessor All decisions are made at the module to allow lower communication speed with substantially improved control panel response time and less sensitivity to line noise and loop wiring properties; twisted or shielded wire is not required.

• Ground fault detection by address Detects ground faults right down to the device level.

Application

The operation of the GSA-MCC1 is determined by their sub-type code or “Personality Code”. The code is selected by the installer depending upon the desired application and is down-loaded the loop controller. Codes 5 and 6 apply to the GSA-CC1/MCC1 only. Code 7 is assigned to the GSA-CC2/MCC2 only and automatically applies to both circuits (A and B)

Installation

GSA-MCC1 : mount the UIO motherboard inside a suitable Kidde enclosure with screws and washers provided. Plug the GSA-MCC1 or GSA-MCC2 any available position on the motherboard and secure the module to the motherboard with the captive screws. Wiring connections are made to the terminals on the motherboard (see wiring diagram). UIO motherboard terminals are suited for #12 to #18 AWG (2.5 mm2 to 0.75 mm2 ) wire size.

GSA-MCC1 Single Input (Riser) Signal Module

Specifications

Catalog Number	GSA-CC1	GSA-MCC1	GSA-CC2	GSA-MCC2
Description	Single Input (Riser) Signal Module		Dual Input (Riser) Signal Module
Type Code	50 (factory set) Two sub-types (personality codes) are available		51 (factory set) One sub-type (personality code) is available (factory set)
Address Requirements	Uses one module address		Uses two module addresses
Wiring Terminations	Suitable for #12 to #18 AWG (2.5 mm² to 0.75mm²)
Mounting	North American 2½ inch (64 mm) deep two-gang boxes and 1½ inch (38 mm) deep 4 inch square boxes with 2-gang covers and GSA-MP mounting plates	Plugs UIO2R, UIO6R or UIO6 Motherboards	North American 2½ inch (64 mm) deep two-gang boxes and 1½ inch (38 mm) deep 4 inch square boxes with 2-gang covers and GSA-MP mounting plates	Plugs UIO2R, UIO6R or UIO6 Motherboards
Operating Current	Standby = 223µA Activated = 100µA
Operating Voltage	15.2 to 19.95 Vdc (19 Vdc nominal)
Output Rating	24 Vdc = 2 amps 25 V Audio = 50 watts 70 V Audio = 35 watts
Construction	High Impact Engineering Polymer
Storage & Operating Environment	Operating Temperature: 32°F to 120°F (0°C to 49°C) Storage Temperature: -4°F to 140°F (-20°C to 60°C) Humidity: 0 to 93% RH
LED Operation	On-board Green LED - Flashes when polled On-board Red LED - Flashes when in alarm/active
Compatibility	Use with: Signature Loop Controller
Agency Listings	UL, ULC, CSFM, MEA, FM

Ordering Information

Catalog Number	Description	Ship Wt. lbs (kg)
GSA-CC1	Single Input Signal Module (Standard Mount) - UL/ULC Listed	0.5 (0.23)
GSA-MCC1	Single Input Signal Module (UIO Mount) - UL/ULC Listed	0.18 (0.08)
GSA-CC2	Dual Input Signal Module (Standard Mount) - UL/ULC Listed	0.5 (0.23)
GSA-MCC2	Dual Input Signal Module (UIO Mount) - UL/ULC Listed	0.18 (0.08)

Related Equipment

27193-21	Surface Mount Box - Red, 2-gang	2 (1.2)
27193-26	Surface Mount Box - White, 2-gang	2 (1.2)
GSA-UIO2R	Universal Input-Output Module Board w/Riser Inputs - Two Module Positions	0.32 (0.15)
GSA-UIO6R	Universal Input-Output Module Board w/Riser Inputs - Six Module Positions	0.62 (0.28)
GSA-UIO6	Universal Input-Output Module Board - Six Module Positions	0.5 (0.23)
GSA-MP2L	Signature Module Mounting Plate, 1/2 extended footprint	1.02 (0.46

Accessories

MFC-A	Multifunction Fire Cabinet - Red, supports Signature Module Mounting Plates	7.0 (3.1)
GSA-MP1	Signature Module Mounting Plate, 1 footprint	1.5 (0.70)
GSA-MP2	Signature Module Mounting Plate, 1/2 footprint	0.5 (0.23)
GSA-MP2L	Signature Module Mounting Plate, 1/2 extended footprint	1.02 (0.46)