Smart 3D Multipoint Sensor Detector GSA-PHS
⭐
✅ The Signature Series Model GSA-PHS Intelligent 3D Multisensor Detector ⭐
✅ gathers analog information each of its two fire sensing elements (photoelectric and heat) and converts it digital signals. The detector’s on-board microprocessor measures and analyzes these signals separately with respect to a third element - Time. We call this technology 3D. It compares the information to historical readings, time patterns, and several known fire characteristics to make an alarm decision. Digital filters remove signal patterns that are not typical of fires. Unwanted alarms are virtually eliminated.
Standard Features
• Integrates photoelectric smoke and 135 º F (57 º C) fixed-temperature heat sensing technologies
• Non-volatile memory
• Automatic device mapping
• Electronic addressing
• Environmental compensation
• Integral microprocessor - intelligent detector
• Wide 0.67% to 3.77%/ft. sensitivity range
• Twenty pre-alarm sensitivity values, set in 5% increments
• Identification of dirty or defective detectors
• Automatic day/night sensitivity adjustment
• Twin RED/GREEN status LEDs
• Standard, relay, fault isolator, and audible mounting bases
• Designed and manufactured to ISO 9001 standards
Installation
Signature Series detectors mount to North American 1-gang boxes, 3-1/2 inch or 4 inch octagon boxes, and to 4 inch square electrical boxes 1-1/2 inches (38 mm) deep. They mount to European BESA and 1-gang boxes with 60.3 mm fixing centers.
Application
Although photoelectric detectors have a wide range of fire sensing capabilities they are best suited for detecting slow, smoldering fires. The table below shows six standard test fires used to rate the sensitivity of smoke and heat detectors. The table indicates that no single sensing element is suited for all test fires. Kidde recommends that this detector be installed according to latest recognized edition of national and local fire alarm codes.
Specifications
Smoke Sensing Element | Photoelectric - Light Scattering Principle |
Heat Sensing Element | Fixed Temperature Alarms at 135ºF (57ºC) Ambient |
Operating and Storage Environment | Operating Temp: 32ºF to 100ºF (0ºC to 38ºC) Storage Temp: -4ºF to 140ºF (-20ºC to 60ºC) Humidity: 0 to 93% RH, Non-Condensing |
Sensitivity Range | ULI/ULC - 0.67% to 3.77% |
User Selected Alarm Sensitivity Settings | Most Sensitive: 1.0%/ft. More Sensitive: 2.0%/ft. Normal: 2.5%/ft. Less Sensitive: 3.0%/ft. Least Sensitive: 3.5%/ft |
Pre-alarm Sensitivity | 5% increments, allowing up to 20 pre-alarm settings |
Operating Voltage | 15.2 to 19.95 Vdc (19 Vdc nominal) |
Operating Current | Quiescent: 45µA @ 19 V. Alarm: 45µA @ 19 V. Pulse Current: 100 µA (100 msec). During Communication: 9 mA maximum |
Construction & Finish | High Impact Engineering Polymer - White |
Compatible Mounting Bases | GSA-SB Standard Base, GSA-RB Relay Base, GSA-IB Isolator Base, GSA-AB4, GSA-AB4G Audible Bases |
LED Operation | On-board Green LED - Flashes when polled . On-board Red LED - Flashes when in alarm. Compatible Remote Red LED (model GSA-LED) Flashes when in alarm. |
Compatibility | Use With: Signature Loop Controller |
Address Requirements | Uses one Device Address |
Agency Listings | UL, ULC, CSFM, MEA |
UL Listed Spacing | 30 ft |
Ordering Information
Catalog Number | Description | Ship Wt. lbs (kg) |
GSA-PHS | Intelligent 3D Multisensor Detector - UL/ULC Listed | .5 (.23) |
TVAdministratorsAdministrators